Injection moulding simulation report
landing_plate_0041
| Model | tmpoaz70bnf.step |
|---|---|
| Material | ABS |
| Solver | grid · 10584 cells |
| Run | b84113369afd |
| Date | 2026-10-16 02:56:28 |
| Units | mm / MPa / °C |
| Software | CavityX 7.0.0 |
| Model | tmpoaz70bnf.step |
|---|---|
| Material | ABS |
| Solver | grid · 10584 cells |
| Run | b84113369afd |
| Date | 2026-10-16 02:56:28 |
| Units | mm / MPa / °C |
| Software | CavityX 7.0.0 |
b84113369afd
· 2026-10-16 02:56:28
| Fill time | 12.091 s |
|---|---|
| Filled | 100.0 % |
| Injection pressure (required) | 80.0 MPa |
| Peak cavity pressure | 37.1 MPa |
| Clamp force | 22.2 t |
| Melt / mould temperature | 229.9 °C / 40.0 °C |
| Cooling time to eject | 9.3 s |
| Volumetric shrinkage | mean 0.91 % · max 1.77 % |
| Max warp deflection | warp could not build a solid mesh of this part: CAD tet mesh failed (gmsh tet meshing failed (exit 1): meshing failed after retries: size 10.2 mm: exit 1 ModuleNotFoundError: No module named 'tetgen'; size 8.2 mm: exit 1 ModuleNotFoundError: No module named 'tetgen'; size 6.56 mm: exit 1 ModuleNotFoundError: No module named 'tetgen'; size 5.25 mm: exit 1 ModuleNotFoundError: No module named 'tetgen'); grid fallback failed (No module named 'tetgen') |
| Part mass | 16.80 g |
| Air traps / weld lines | 0 / 0 cells |
| Short shot | 0 cells |
| Volume | 16.000 cm³ |
|---|---|
| Surface area | 167.2 cm² |
| Bounding box | 100.00 × 80.00 × 2.00 mm |
| Wall thickness | 2.14 mm mean |
| Part mass | 16.80 g |
| Grid cells | 10584 wall / 10584 total |
| Cell size | 2.381 × 1.905 × 0.333 mm |
| Grid reach | 100.0 % of 1 region(s) |
| Compute backend | CPU (SciPy SuperLU direct) |
| Solve wall time | 10.1 s |
| Material | ABS |
|---|---|
| Injection pressure | 80.0 MPa |
| Melt temperature | 229.9 °C |
| Mold temperature | 40.0 °C |
| Pack pressure | — |
| Number of gates | 1 |
| Control mode | pressure-controlled |
| Required / used injection pressure | 80.0 MPa |
| Mean flow rate Q = V/t | 1.34 cm³/s |
| Gate pressure drop | 42.5 MPa |
| Peak cavity pressure | 37.1 MPa |
| Gate shear rate | 9,700 1/s (limit 50,000) |
| Machine max pressure | not set |
| Air traps | 0 (0 not reachable by a parting-line vent) |
|---|---|
| Weld / meld lines | 0 cells, 0 head-on |
| Hesitation | 0 cells |
| Short shot | 0 unfilled wall cells |
| Shear rate | max 505 1/s (limit 50000); 0 cells over; shear heating ≈ 1.6 K |
| Sink marks | 0 cells, est. max depth 0.00 mm |
| Clamp force | 22.2 t (projected area 80.0 cm²) |
| Pack pressure | 40.0 MPa (default 50% of injection) |
|---|---|
| Hold ends | 14.47 s (gate freeze 2.38 s) |
| Volumetric shrinkage | mean 0.91% · max 1.77% |
| PVT data | Kastelic et al. 2026, Polymers 18:1310, Table A2 (ABS Polylac PA757) |
| Pack model | time-stepped compressible pack/hold (Tait, Hele-Shaw, slab cooling) |
| Pressure at end of hold (max) | 34.4 MPa |
| Part mass | 16.47 g at end of fill → 16.55 g (+0.08 g fed during pack) |
| Warp | warp could not build a solid mesh of this part: CAD tet mesh failed (gmsh tet meshing failed (exit 1): meshing failed after retries: size 10.2 mm: exit 1 ModuleNotFoundError: No module named 'tetgen'; size 8.2 mm: exit 1 ModuleNotFoundError: No module named 'tetgen'; size 6.56 mm: exit 1 ModuleNotFoundError: No module named 'tetgen'; size 5.25 mm: exit 1 ModuleNotFoundError: No module named 'tetgen'); grid fallback failed (No module named 'tetgen') |
Accuracy limits: packing is a time-stepped compressible Hele-Shaw solve (Tait PVT) with first-mode slab cooling and frozen-layer growth, gate held at the set pack pressure (no runner/nozzle losses); residual stress from a layered thermo-viscoelastic model (in-mould constraint, Maxwell relaxation); fiber orientation is a fill-direction approximation, not Folgar-Tucker. Published benchmarks: within ~2x on a mould-ΔT case, large under-prediction on flat plates warped by unmodelled effects (see review); treat values as trend indicators, not tolerances.